profile - Razi University

Faculty Member of Razi University

Razi University
Hamdi Abdi

Hamdi Abdi

Professor / Engineering / Dept. of Electrical and Electronic Engineeingِِِ

Current courses

Course Name unit term
Advanced power system operation 3 first semester Academic year 2026-2027
3 first semester Academic year 2026-2027

Master Theses

  1. Smart load management for enhancing grid stability
    AHMED SALIH MOHAMMED 2026
    Cardiovascular diseases are one of the leading global causes of mortality, and rapid diagnostic modalities would be invaluable for determining pre-clinical signs. While the ECG is the main non-invasive tool for arrhythmia diagnosis, many automated ECG analysis systems are based purely on one-dimensional signal processing algorithms and therefore often fails in relation to diagnosing complex morphological variations. Prior work often divides signal and image space and neglects the inherent use of visual morphology by clinicians. To fill this void, the presented thesis proposes a new dual-domain framework for QRS-complex detection and heart-beat >  It is based on data available until October 2023 and uses the MIT-BIH Arrhythmia Database, aggregating heartbeats into two main clusters (normal and abnormal >  The QRS detection part obtained a very good sensitivity (99.90%), a positive predictivity of 98.99%, and an error rate value of only 1.12 %. Results: The signal-only model outperformed the >  
  2. AI Based distribution network state estimation
    NOORULDEEN HASHIM KAREEM 2026
    State estimation is a fundamental task in the monitoring and operation of electric power distribution networks, where accuracy and speed play a crucial role in maintaining real-time situational awareness of the grid. This thesis presents the development and evaluation of a multi-area, data-driven framework for distribution network state estimation. In the proposed framework, the network is partitioned into five areas; following feature engineering based on mutual information, various models—including Linear Regression, Lasso, ElasticNet, Multilayer Perceptron (MLP), and an Ensemble model—were employed to estimate voltage magnitude and phase angle. The method's performance was evaluated using standard 33-bus and 69-bus networks, utilizing metrics such as Mean Absolute Error (MAE), Root Mean Square Error (RMSE), and Maximum Error (MaxError). The results demonstrated that the regression models achieved voltage estimation accuracy comparable to the MLP, while their training times remained under 2.5 seconds for both networks; in contrast, training the MLP required approximately 45.2 seconds for the 69-bus network and 47.1 seconds for the 33-bus network. Under conditions of full observability, the ensemble model achieved a maximum error of 0.309% for voltage and 0.1337 degrees for phase angle in the 69-bus network. Corresponding values ??for the 33-bus network were 0.406% and 0.2294 degrees, respectively. Compared to the reference study [53], which reported a maximum voltage error of 0.30% and a phase angle error of 0.34°, the proposed method performed comparably in terms of voltage error and superiorly in terms of phase angle estimation for the 69-bus network; for the 33-bus network, although the voltage error was higher, the phase angle error remained lower than the reference value. Furthermore, the multi-area structure in the 69-bus network reduced the total training time from 153.94 to 117.71 seconds—a reduction of 23.5%. The study's primary innovation lies in presenting and evaluating an integrated framework comprising multi-area estimation, mutual information-based feature engineering, simultaneous comparison of regression and neural network models, and their combination into an ensemble model; this approach enables the simultaneous assessment of accuracy, computational cost, and robustness against measurement loss. Keywords: State estimation, distribution network, artificial intelligence, ensemble model.   
  3. Solving the economic load dispatch problem using Hybrid Particle Swarm and Grey Wolf optimization algorithms
    SAJJAD HAITHAM QASIM 2026
       Abstract: Economic Load Dispatch (ELD) is one of the fundamental operational problems in power systems. Its objective is to determine the optimal power generation of generating units while minimizing fuel costs and satisfying operational constraints. In this study, a hybrid GWO-HPSO algorithm is developed to improve the balance between exploration and exploitation. To enhance the search capability of the proposed method, three mechanisms, including nonlinear inertia weight reduction, adaptive Cauchy mutation, and SQP-based local search, are incorporated into the algorithmic framework. The performance of the proposed method is evaluated on standard 3-, 13-, and 40-unit systems under various operating conditions, including the valve-point effect, transmission losses, and the Combined Economic and Emission Dispatch (CEED) problem. The results for the 40-unit system show that the improved algorithm achieves a best cost of $121,595.63/h and a mean cost of $122,584.98/h, outperforming PSO, GWO, and the original hybrid algorithm. Compared with the standard GWO algorithm, the proposed method achieves an approximately 1.744% reduction in the best cost. Furthermore, in a direct comparison with the WHOA algorithm reported in the reference study, the obtained cost is approximately 0.0165% lower. In the environmental analysis, emission coefficients are explicitly reported, while the actual generation cost and emissions are calculated independently. The CEED analysis indicates that moving from a purely economic operating condition to a condition with full environmental priority reduces emissions by approximately 14.98%, 87.88%, and 52.33% in the 3-, 13-, and 40-unit systems, respectively. The results demonstrate that the proposed method has a strong capability to solve non-convex, multimodal, and large-scale optimization problems and can provide an appropriate trade-off between economic and environmental objectives. Keywords Economic Load Dispatch (ELD); Hybrid Optimization; PSO-GWO; Multi-objective Optimization   
  4. Forecasting Macroeconomic Variables Under Uncertainties of Geopolitical Economic Policies
    Haniyeh Lotfi 2026
       Abstract In recent decades, the global economy has been increasingly influenced by various forms of economic, political, and geopolitical uncertainty. These uncertainties, arising from changes in government economic policies, international tensions, geopolitical developments, and global shocks, can generate significant fluctuations in macroeconomic variables. Under such circumstances, the accurate forecasting of key economic variables, including inflation, unemployment, and economic growth, has become one of the most important challenges for researchers and economic policymakers. Moreover, the rapid expansion of communication technologies and the emergence of social media platforms such as Twitter (X) have accelerated the dissemination of economic and political information, which may intensify market reactions, increase economic volatility, and create complex and unpredictable economic environments. Within this framework, the present study aims to forecast major macroeconomic variables, including inflation, unemployment, and economic growth, under conditions of economic policy uncertainty and geopolitical risk. This study examines selected developed countries (G7 countries including the United States, Canada, Germany, France, the United Kingdom, Italy, and Japan) and selected developing countries (India, Malaysia, Thailand, Vietnam, the Philippines, Pakistan, and Indonesia) over the period 2005–2025 in order to enable a comparative analysis of the behavior of these variables across economies with different levels of development. Focusing on these two groups of countries makes it possible to better analyze the impact of global uncertainties on different economic structures and their degree of vulnerability to economic shocks. To achieve the research objective, a hybrid approach of the decomposed wavelet neural network was used and compared with econometric models including Random Walk, ARMA and GARCH. The results showed that the hybrid model of the decomposed wavelet neural network has superior performance in predicting macroeconomic variables compared to competing econometric models. Also, using this hybrid model, each of the macroeconomic variables was predicted for the next 5 years for all selected countries. The findings of this study can offer a better understanding of how economic and geopolitical uncertainties affect the behavior of macroeconomic variables. The results may also be useful for economic policymakers, planners, and decision-makers in both developed and developing countries, as more accurate forecasting of macroeconomic variables can contribute to the adoption of more appropriate economic policies and the better management of economic shocks. In addition, by presenting a novel hybrid approach in the field of economic forecasting, this research can contribute to the development of the scientific literature on the application of artificial intelligence and machine learning methods in the analysis and prediction of macroeconomic variables. Keywords: Economic policy uncertainty, geopolitical risk, economic forecasting, decomposed wavelet neural network
  5. برنامه ريزي توسعه توليد سيستم تركيبي هسته اي و انرژي هاي تجديدپذير مبتني بر مدلسازي عدم قطعيت ها
    Alireza Soheili 2025
  6. Energy performance of photovoltaic high-rise office buildings integrated with battery storage system
    Mohammad Hossien Gheymasi 2025
  7. Application of neural networks in detecting cyber-attacks of modern power systems Thesis Title:
    Karim Shahbazi 2025
      Modern power systems rely on advanced technologies and communication networks that enable efficient monitoring, control, and operation of physical equipment. These tools offer diverse services in terms of functionality and enhanced reliability; however, their increasing use has led to a rise in vulnerabilities and cyberattacks. Such vulnerabilities have serious consequences, including blackouts and detrimental effects on electrical infrastructure. Therefore, developing effective models for identifying and classifying adverse events in power systems for the prompt issuance of control commands is of great importance. In this context, cyberattacks on SCADA systems, which are widely used for monitoring large production systems and modern power networks, have become a significant challenge. These systems are particularly vulnerable to various cyberattacks due to their unique features, including remote communications and management of critical infrastructure. Detecting these attacks using traditional Intrusion Detection Systems (IDS) is challenging due to the complexity and diversity of threats, highlighting the need for innovative and effective methods for accurate identification of these attacks. In this regard, a two-stage feature selection method utilizing Principal Component Analysis (PCA) and the War Strategy Optimization (WSO) algorithm, along with a Feedforward Neural Network (FFNN), has been proposed. In this method, the number of layers and the number of neurons in each layer of the FFNN are optimally determined by the WSO algorithm. This approach is designed for the precise identification of malicious attacks. The performance of the proposed method has been evaluated using laboratory SCADA system data, and the results demonstrate satisfactory effectiveness in detecting cyberattacks. This research can significantly enhance the resilience and safety of SCADA systems against cyber threats and serve as an effective solution for managing and mitigating risks arising from cyberattacks on critical infrastructure.
  8. Providing a new method for islanding interconnected power systems
    Kambiz Saydei rashbogari 2024
    Abstract The islanding of interconnected power systems, which is also known as the isolation and breaking of power systems, is the last defense method to deal with the collapse of the system and prevent the occurrence of catastrophic events in the power network, which as a widespread control method is a comprehensive decision problem with There are many details and it is presented as an important part of corrective control strategies. After the occurrence of a major disturbance in a power system, if there is no suitable solution plan and model in time, this disturbance may lead to the total collapse of the system. Islandization of power systems means determining the correct points of isolation of the integrated system into a number of smaller islands if maintaining the integrity of the system is not possible. The aim of this thesis is to provide a method to predict the appropriate time for applying controlled islanding in the network by means of indicators based on the relationships between the generator harmonic groups. The defined indicators can predict the weakening of security and fragility of the network in the context of the dynamic behavior of the system and as a result the islanding of the network with high speed and accuracy and in a timely manner. The IEEE 39 bus network has been used to obtain the critical limit of the introduced indicators in a timely manner and to predict the appropriate time for islanding in a timely manner. The results obtained from the dynamic simulation indicate that the controlled islanding at the right time can prevent the occurrence of consecutive incidents, global blackouts and crises in the network.   
  9. The effect of the stiffness of the surface layer of the soil near the foundation on the seismic deformations of the shallow foundation located on the slope
    Sobhan Shekarbeigi 2024
    در اين مطالعه هدف مدلسازي اثرات سختي لايه خاك ماسه اي شيب دار بر رفتار تغييرشكلي شيب و پي سطحي مجاور شيب است. سختي ارتجاعي خاك كه متناظر با تغييرات سرعت موج برشي و موج فشاري مصالح ماسه اي است در تحليل هاي عددي پارامتري مختلف منظور شده است. در اين پژوهش، حدود 10 مدل عددي با تغيير سختي ارتجاعي خاك ماسه اي كه معادل چهار نوع زمين مندرج در آيين نامه زلزله 2800 است گسترش داده شده است. مدل هاي عددي در قالب كرنش مسطح و در برنامه نرم افزاري تجاري-تحقيقاتي PLAXIS 2D ايجاد شده اند. ركورد زلزله نزديك-گسل شامل مولفه افقي طولي زلزله ازگله-سرپل ذهاب در ايستگاه لرزه نگاري شهر سرپل ذهاب به عنوان تحريك لرزه اي ورودي مدل هاي عددي منظور شده است. با مقايسه نتايج نسبت تنش هاي برشي دو نمودار خروجي كه اختلاف مدول ارتجاعي آنها 63/15 برابر است، نتيجه مي شود كه با افزايش ميزان سختي ارتجاعي مدل عددي، از ميزان تجمع و تمركز تنش هاي برشي نسبي زير پي در ناحيه گوه گسيختگي پي سطحي، كاسته مي شود و به توزيع تنش هاي برشي بخش ناپايدار شيب و قوس لغزش شيب افزوده مي شود. با افزايش مقادير سختي خاك، تغيير محل تنش هاي برشي تا آنجا پيش مي رود كه مقدار زيادي از تنش زير پي كاسته مي شود و علت آن نيز اثر همزمان وجود سربار استاتيكي (100 كيلوپاسكالي) روي پي سطحي (بار معادل ساختمان يا سازه) و سخت شدن ناشي از بارگذاري ديناميكي و وقوع كرنش هاي برشي سيكلي در مصالح ماسه اي است.   از طرفي، با مقايسه پاسخ جابه جايي جانبي براي نقاط چهارگانه در مدل با سختي ارتجاعي E=500MPa و در مدل با سختي ارتجاعي E=1000MPa، بازهم رفتار كلي مدل عددي، شاهد كاهش جابه جايي هاي نقطه C در بالادست تاج شيب است. در واقع نكته قابل برداشت از اين نتايج آن است، كه جابه جايي هاي لرزه اي جانبي شيب بيشتر از آن كه با افزايش سختي مصالح، كاهش پيدا كند، به طور غالب تحت تاثير دوري يا نزديكي نقاط به تاج شيب و قسمت شيب دار است. به گونه اي كه هر چه قدر نقاط مورد بررسي از تاج شيب فاصله بيشتري داشته باشند، بيشتر هم تحت تاثير افزايش سختي مصالح ماسه اي خشك قرار مي گيرند و از جابه جايي هاي لرزه اي وقوع يافته در آنها (به مقدار بيشتري) كاسته مي شود و هر چه قدر به تاج شيب و قسمت شيب دار نزديك تر باشند، تحت تاثير ناپايداري ذاتي هندسي شيب قرار مي گيرند و افزايش دو يا چند برابري سختي مصالح كمتر از موضوع اوليه ناپايداري شكل-هندسي شيب (در اثر رخداد بارگذاري لرزه اي جانبي) آنها را تحت تاثير قرار مي دهد. البته خاطرنشان مي گردد كه نكته مهم در خصوص تغيير سختي لايه خاك ماسه اي در حين بارگذاري هاي لرزه اي آنست كه با تغييرات سختي لايه خاك ماسه اي خشك در شيب، فركانس طبيعي ارتعاش آن نيز كه تاثير مستقيم بر بزرگنمايي يا تضعيف دامنه پاسخ هاي شتاب لرزه اي ناشي از امواج لرزه اي دارد، تغيير مي كند. به همين دليل است كه در زمان هاي آغاز و نزديك به پايان بارگذاري لرزه اي، اغلب مدل هاي عددي مختلف پاسخ هاي بزرگنمايي مختلفي بدست داده اند.   
  10. Study of bearing capacity of single foundations on reinforced recycled soils
    Ghane Valizadea 2024
  11. Investigating the energy consumption pattern of different customers in Kermanshah city
    Reza Farrokhi 2024
  12. Solving the economic load dispatch problem considering transmission losses with HOA algorithm
    Mohammadhossin Seifipour 2024
  13. Investigating the effects of energy storage systems on the optimal management of a renewable energy microgrid
    Neda Shahnejat 2024
    In independent microgrids located in remote areas, the development of reliable and self-sufficient renewable energy systems is one of the major challenges of operating power systems due to the lack of connection with the national power grid. One of the best future options for increasing the use of renewable energies in grid-independent systems is the use of energy storage systems. In this thesis, an optimization model is proposed to determine the most cost-effective combination of renewable energy capacity using the war strategy optimization algorithm in a grid-independent microgrid supported by battery energy storage technology. The problem of energy management has been formulated using linear programming and the proposed algorithm has taken into account the limitations of exploitation, technical and land use. Also, the hourly effects of the region's weather and load demand, along with the installation price, have been evaluated. The simulation results for the diesel-based microgrid, which is a benchmark, and the renewable microgrid based on LCOE (levelized cost of electricity), have been compared and analyzed. In addition, sensitivity analysis is also presented to investigate the effect of variables on LCOE and PC (present cost) of the system. According to the tests and the obtained results, the lowest amount of PC is related to the scenario that has both a reduction in storage costs and a reduction in demand for consumption, which is 2113200 (€). Also, the results in this section show that the renewable microgrid has a higher LCOE (from 0.39 to 0.48 (€/kWh)) than the diesel-based approach (from 0.21 to 0.48 (€/kWh) is watt hours.   
  14. Consumer-Centric Reliability Assessment of Distribution System Considering Feeders with Different Load Types and Cost-Benefit Sensitivity Analysis
    Farshad Zangishei 2024
  15. Optimal power flow for minimizing the fuel cost generation considering TCSC
    Behzad Fatehi 2024
  16. Investigation and simulation of random Ferroresonance phenomenon in power transformers
    Majid Soleimani Saeed 2023
       The quality of power and lack of use of the network are considered as two important factors in power networks, and one of the factors of ferroresonance is known as these network disturbances, which with the occurrence of this phenomenon, power quality and network security are endangered. Ferroresonance is one of the rare phenomena in power networks. In this project, first by introducing the phenomenon of ferroresonance, its different random states in the power system are explained, and also the effects in different fields are presented to start sales. Investigating and simulating the ferroresonance phenomenon is dependent on the ferroresonance circuit model and finding its state equations. In this project, by solving these equations, we investigate and simulate the random ferroresonance in the power transformer. Finally, we examine the effect of the initial conditions on this phenomenon in the power transformer. Usually, in the ferroresonance equivalent circuit, the self-impedance of the network and its resistance value are ignored, and in this project, we study the effect of ignoring these parameters.
  17. Constant power load control in DC microgrid to increase the stability using energy storage system
    2023
      Objective: Improving output waveforms and overcoming theinstability effect caused by CPLs in DC microgrid is the main objective of thisresearch.
  18. Distributed optimization for control and modeling of DC micro grids using hybrid storage systems
    2023
  19. Applying data mining to forecast generated power by solar power plant used in probabilistic optimal power flow
    Negin Fatahnia 2022
    Abstract  The increasing influence of renewable energy sources, including solar energy, in the production of electrical energy, has increased uncertainties in solving various problems,control and operation of the power system.The increasing influence of renewable energy sources, including solar energy, in the production of electrical energy, has increased uncertainties in solving various problems, control and operation of the power system.The increasing influence of renewable energy sources,including solar energy, in the production of electrical energy, has caused an increase in uncertainties in solving various problems, control and exploitation of the power system.this reason, probabilistic load distribution has become an important tool for investigating the random characteristics of the power system.In this thesis, in order to investigate the amount of losses, considering the unstable behavior of loads in the form of a normal distribution, one of the Monte Carlo probabilistic load distribution methods is used.Two-point, three-point and five-point estimation are used with the help of Matlab software. In the following, the MCS&3PEM algorithm is proposed and the results obtained from it are compared with the Monte Carlo method.Also, in order to check the amount of fuel cost, the PSO algorithm has been used; PSO The obtained results will be evaluated to find the best location of photovoltaic systems, in order to reduce the cost of fuel. Two standard test systems are used to check the said methods. Also, to estimate the amount of solar radiation received in Kermanshah province using daily data obtained from meteorological station, in a period of 6 years, GMDH optimized neural network is proposed. Also, to estimate the amount of solar radiation received in Kermanshah province using daily data obtained from meteorological station, in a period of 6 years, GMDH optimized neural network is proposed.Also, to estimate the amount of solar radiation received in Kermanshah province using the daily data obtained from the weather station, in a period of 6 years, an optimized GMDH neural network is proposed.The results of the research showed that there is a small difference between the radiation values measured at the meteorological station and the radiation obtained by the model, which shows the ability of the model to estimate the radiation. The results of the research showed that there is a small difference between the radiation values measured at the meteorological station and the radiation obtained by the model, which shows the ability of the model to estimate the radiation.The results of the research showed that there is a small difference between the radiation values measured at the meteorological station and the radiation obtained by the model, which indicates the ability of the model to estimate radiation.In order to evaluate different modes of system operation, two scenarios areconsidered. First, all the loads are fed only by the main grid, and losses and production costs are expected to be high. And second, the photovoltaic system is connected to the system. Based on the results,In order to evaluate different modes of system operation, two scenarios are considered. First, all the loads are fed only by the main grid, and losses and production costs are expected to be high. And second, the photovoltaic system is connected to the system. Based on the result،In order to evaluate different modes of systemoperation, two scenarios are considered. First, all the loads are fed only by the main grid and the losses and production costs are expected to be high. And second, the photovoltaic system is connected to the system. Based on the It was found that when the photovoltaic system is connected to the system, the amount of power loss and production cost   is reducedKeywords:
  20. Investigation of the effect of some variables of sandblasting process, acid washing and heat treatment on the surface properties and cellular response of titanium.
    Dariush Danyali 2022
          In recent years and with the increase in the number of elderly people in different countries, the supply and demand for the use of titanium and its alloys in the manufacture of implants used in the human body such as hip joint prosthesis, joint replacement, knee replacement, fracture fixation and dental implants have increased.   has increased widely.   In medical applications, in addition to the usual properties of alloys, other factors such as topography and surface energy are also considered, which play an important role in the adhesion of bone cells to the implanted surface.   As a result, the surface of the material plays an important role in the body's response to the implantable material.   The purpose of this research is to investigate the effect of some variables of the sandblasting process, acid washing and heat treatment on the surface characteristics and cellular response of titanium.   In order to modify the surface of the titanium substrate, first the samples were sandblasted using alumina powder, then they were etched in a solution containing nitric acid and sulfuric acid for the necessary time.   After that, the samples were placed in the oven at temperatures of 300, 400, and 500 degrees Celsius for one hour. A group of samples were left without heat treatment.   In order to measure roughness, hydrophilicity, investigate surface morphology, investigate phase compounds, cytotoxicity and biocompatibility of substrates, various tests and equipment including roughness meter, water contact angle measurement system, XRD, cytotoxicity and SEM were used to investigate cellular morphology.   The results of the X-ray diffraction test showed that the dominant phase formed is the Ti6O phase.   Of course, a small amount of Ti2O3 was also formed.   The above groups cause better calcium deposition through reaction with body fluids.   And the results of the hydrophilicity test showed that the amount of wetting angle ?m decreased with increasing sandblast pressure and especially with heat treatment compared to the control samples.   However, in most of the samples, by increasing the temperature of heat treatment to 500 degrees Celsius, the contact angle has increased and the wettability has decreased.   Regarding the evaluation of cell viability, the produced levels did not show any signs of cytotoxicity.   In fact, the roughness of the surfaces obtained after sandblasting and acid etching were able to strengthen the attachment and proliferation of MG-63 cells on their surfaces.
  21. Combined heat and power economic dispatch problem considering power loss by applying the meta-heuristic algorithms
    Mohamad hadi Heidary 2022
    Due to the production of electrical energy in thermal power plants, a lot of heat enters the atmosphere through cooling towers. Therefore, the energy efficiency of these types of power plants decreases (the efficiency of these power plants is between 50 and 60 percent). Therefore, a problem named Combined Heat and Power Economic Dispatch (CHPED) plays an important role in the field of power system research because it helps to reduce production costs and also reduce pollutants emitted into the atmosphere by using waste heat through steam. In order to effectively and optimally use cogeneration units, the economic dispatch of heat and power load is considered, the purpose of this problem is to find the optimal point of power and heat production with minimum fuel cost in such a way that both heat demand and power demand can be provided  
  22. Optimal energy management in a distribution microgrid containing distributed fuel cell generation sources and energy storage devices
    Sepideh Asadimanesh 2022
  23. Security Constrained Optimal Power flow in distribution microgrids considering uncertainties
    Ramin Moradi 2022
  24. Optimal Stochastic Placement and Capacity Determination of charging stations of electric vehicles considering the uncertain loads by using the Monte Carlo Simulation
    Ali Shahbazi 2021
      Today, access to energy is very important for developed and developing countries, and because these resources are in crisis, they cannot be trusted and a solution must be found. Therefore, the use of electric vehicles is a very good option to replace combustion vehicles in order to reduce fuel consumption and provide power in the form of distributed generation. But the point is that the community of electric vehicles at charging stations can have a huge impact on the network, and charging stations can also play a role. On the other hand, the location of charging stations in the network plays an important role in network parameters such as losses and voltage deviations. Also, the probabilistic behavior of load in the network and its changes during 24 hours a day can have a significant impact. Have power on network lines during playback. Therefore, in this dissertation, we first model and review electric car charging stations affected by the behavior of electric car owners by including load uncertainty in the Monte Carlo distribution method, which has been omitted in previous studies. Then, to determine the optimal location and capacity of electric vehicle charging stations in the 33-bus distribution network in order to reduce the negative effects on the network, including increasing network losses (active and reactive) and voltage deviations in the network bus using the algorithm. Gravitational atmosphere is addressed. The results of simulation in MATLAB software environment show an increase in losses and deviation of network voltage by placing electric car charging stations in place and with optimal capacity due to increased current and power passing through the lines. The instrumentation shows that if the charging stations of the electric vehicle are not in the optimal location, the losses and voltage deviations will be much higher than the nominal values ??of the network.
  25. Solving Combined Heat and Power Economic Dispatch Problem in Multi-zone Power Systems Using Meta-heuristic Algorithm
    Amir Nazari 2021
  26. Damping of multi machines power system oscillations by using of multiband pss
    Azar Ghasemi 2021
    The stability of the power system refers to the ability to maintain or return to the working point of the persistent state of the power system when it is disturbed. Turbulence may have a serious effect on the stability of the power system due to the stability of the small signal and the large signal. Increasing the consumption and diversity of consumers of electrical energy in power systems has led to an increase in the amount of energy transmitted in power systems. This increase has led to the interconnectedness of power systems to provide the required energy. In these interconnected systems, low frequency fluctuations can increase. These fluctuations affect the security and stability of large power systems and limit the current of power in the communication lines between the power sub-systems. Normally, synchronous generators maintain a constant vetting and a constant relative angle between stator and rotor coils, which is called synchronous generators in power systems. As soon as disturbances occur, the ability of the synchronum generator to balance the mechanical power of the turbine generator and the electrical power of the load to maintain stability is controlled. Traditionally, in the control of synchronous generators, a power system stabilizer (  ) produces an additional drive signal for the AVR excitation system to drive low frequency fluctuations. The goal is to create more mirant torque. On the other hand, installing    on all production units may lead to unwanted dynamic interactions. Matlab programming to combine probable load spreading analyses, linear modeling of multi-machine power system, small signal analysis and    optimization with pso metaheuristic algorithm for critical generator based on single-way stabilizers that have performance capability To have the best, it will be done.  
  27. Optimal placement of charging stations of electric vehicle using the heuristic methods
    Maryam Lotfi 2021
    Today, electric vehicles are a suitable alternative to internal combustion vehicles due to their higher efficiency and far less environmental damage than internal combustion vehicles. But the factors that limit the use of these vehicles are issues such as the limitation of a city in having adequate communication routes and parking infrastructure and their charging stations. On the other hand, although the capacity of these vehicles alone is limited, a set of these electric vehicles at charging stations turns them into a unit that has the ability to appear in the role of a relatively large load for the network. Therefore, in order to make the best use of electricity distribution networks, it is necessary to operate and find the optimal location and capacity of charging stations for electric vehicles. In this regard, in this thesis, an attempt has been made to improve the IEEE 69_BUS TEST SYSTEM by determining the optimal location and capacity of electric vehicle charging stations based on the actual conditions of the power system.. For this purpose, uncertainty due to the number of vehicles in each charging station has been considered. The objective function in the present problem is multi-objective with the objectives of reducing losses (active and reactive) and reducing voltage deviation, which is optimized using the particle swarm algorithm and genetic algorithm in the MATLAB software platform and the results obtained from the location are compared.   
  28. Solving economic emission dispatch problem in combined heat and power systems using the grasshopper behavior-based algorithms
    Yaganeh Sharifian 2021
  29. Solving the stochastic unit commitment problem considering wind power generation uncertainty and modeling the electrical losses in transmission system
    Maryam Najafi 2021
  30. Energy Management in A Multi-agent-microgrids
    Farhood Ghalkhani 2020
  31. Probabilistic Optimal Power Flow in Hybrid AC/DC Grids Considering the Impacts of Wind Power Plants and Photovoltaic Systems
    Seyedeh armaghan Jasemi 2020
  32. Combined Heat and Power Economic Dispatch (CHPED), and Emission Economic Dispatch (CHPEED) Applying Heuristic Algorithm
    Hossein Norianfar 2019
    Abstract Economic dispatch is one of the most important problems in operation of power systems. The purpose of the economic dispatch problems is to obtain the generation power units in a way that supplies the demanded loads (including electrical and thermal powers) and meet different constraints at minimum cost. On the other hand, with increasing pollutants and environmental pollution, concerns have been raised. For this reason, the economic emission dispatch problems, which are considered in both sides, are very important today. On the other hand, due to the failure of classical and mathematical methods, to solve these problems, considering the various restrictions of power system, due to the existence of local minimums, nonlinear, non-convex, and non-smooth of the problem, the use of evolutionary optimization methods has been increased. Therefore, in this thesis, ICA algorithm, hybridizing TVAC-PSO with EMA algorithm, and a new method based on fast non-dominated sorting and dynamic crowding distance are used to solve problems of CHPED, CEED, and also solving multi-objectives problems of CHPEED and DEED. In each case, each one is applied on several test systems and their results are compared with those obtained from other known methods, the results of which show the effectiveness and superiority of the proposed methods over other methods, in each of these fields. In addition, the statistical comparison results of the proposed new method prove its robustness and reliability. Also, a constraint handling technique, for the first time in the field, is integrated into the proposed hybrid algorithm, and its effectiveness in satisfying constraints at least cost compared to other methods is shown in constrained CEED problem. Finally, in order to evaluate the proposed hybrid algorithm in solving practical problems, a new dynamic multi-objective test system is introduced and solved by considering system practical constraints, such as ramp rate limit, prohibited operating zones, valve point loading effect, spinning reserve, transmission electrical losses and multi-fuel.Satisfaction of all of these constraints indicates the appropriateness of the procedure used in this algorithm. o Keywords: Economic Dispatch, Transmission Electrical Losses, Multi-fuel, Spinning Reserve, Valve Point Loading Effect, Prohibited Operating Zones, Constraint Handling, Dynamic Economic Emission Dispatch  
  33. Optimal power flow in hybrid electric and gas networks aiming to reduce operational and emission costs
    Navid Azadi 2019
  34. Optimal Allocation of CHP(Combined Heat and Power) Considering Air Pollution Cost
    Saeed Yadegari 2019
  35. Analyzing the impacts of battery energy storage systems (BESSs) on power system stability including wind power plants (PMSG type) and optimizing their application based on evolutionary algorithms
    RAMIN SAKIPOUR 2018
  36. Probabilistic Optimal Power Flow in the presence of uncertainties applying Cultural Algorithm
    Hossein Mansouri 2018
      Fossil fuels are declining as sources of human consumption over the years, and in addition to the greenhouse gas emissions that result from these fuels, they are damaging our planet. Renewable energies as a solution to reduce the adverse effects of reducing fosil energy reserves, resulting in an intensification of the global energy crisis as well as an increase in greenhouse gas emissions resulting in harm to the environment. In addition to using these resources, network planning should be done in such a way as to minimize the economic cost to the network. In this case, power plants with a higher fuel cost with less power and low fuel-efficient power plants enter the service with more power. This operation is performed according to load balancing equations and pseudo-security assertions, which is known as the optimal load distribution name. If the problem of optimal load transfer includes random input variables such as the power output of the wind power plant, the output of the problem will also be random, so this type of problem-solving optimal load transfer problem is called optimal load probability. In this paper, for the first time, the Cultural Algorithm (CA) is applied to solve the probable optimal power flow problem in the presence of wind power plants uncertainties and taking into account the power network constraints. The Cultural Algorithm is used as a general optimization method for nonlinear and non-convex functions and can substantially shift the target functions with respect to the problem constraints towards the optimal solutions. In this paper, various methods regarding to generation changes in the structure of the algorithm are also compared and investigated. In addition, the improvement methods of the proposed algorithm applied to limited input problems has been discussed and detailed, especially on optimal power flow problem concluding the uncertainties. The ability of the presented algorithm in optimizing the described problem for IEEE standard 30 and 57 buses test cases has been addressed and challenged using MATLAB software among the other well-known algorithms in this field.
  37. The Development Plan of The Football Stadium (Case Study: Football Stadium With Fifteen Thousand seat, Kermanshah, Iran)
    2018
  38. .
    Ehsan Khanmohamadi 2018
  39. .
    Fateme Rastegarzade 2018
  40. Reliabilityassessmentof smart grid considering the self-healing effect in presence of distributed generation
    Sanaz Ghanbari 2018
    بررسي قابليت اطمينان شبكه هوشمند با لحاظ نمودن خودترميمي شبكه در حضور منابع توليد پراكنده
  41. Study of the synthesis of zinc oxide nanocrystals by sol-gel method and optimization of the parameters affecting the grain size by Taguchi method
    Ahmad Riahi 2018
    study
  42. پخش بار بهينه مقاوم با لحاظ نمودن قيود امنيتي در حضور عدم قطعيت بار و نيروگاه بادي
    Eshrat alsadat Ghasemi 2018
  43. Dynamic Optimal Power Flow in Active Network Managements Applying Wind and Solar Renewable Energy
    Saeed Ranaei 2018
  44. Considering the behavior of different metals on nano-boehmit basis in producing Biodiesel
    ROONAK KORDESTAN SHAHOO 2018
    چكيدهدر اين پايان نامه از يك كاتاليست ناهمگن بازي برايتوليد بيوديزل استفاده شد و بهينه سازي صورت گرفت.براي تهيه كاتاليست   از   بوهميت به عنوان پايه استفاده شد و 10 فلز مختلف( كلسيم، منيزيم، روي، منگنز،كبالت،باريم،نيكل، استرانسيم، لانتانيوم، سريم) رويپايه قرارگرفت.10 كاتاليست سنتز شده تحت شرايط يكسان(6درصد وزني كاتاليست، نسبتمولي متانول به روغن 15:1، دماي 65 درجه سلسيوس و زمان 8 ساعت) تست شدند.از ميانآنها CaO/AlOOH داراي بالاترين بازده بود.براي بهينه كردن بازدهبيوديزل از روش سطح پاسخ با باكس بنكن استفاده شد.شرايط بهينه به دست آمده درواكنش تبادل استري شامل 75/3 درصد وزني كاتاليست،نسبت مولي متانول به روغن 33/8،102 دقيقه زمان انجام واكنش و دماي واكنش c°65   مي باشد.بازدهبيوديزل تحت شرايط بهينه % 2/99   به دستآمد.اين كاتاليست 4 بار قابليت بازيابي دارد و  بازده بيوديزل با كاتاليست بازيابي شده، بيشتر از 75 درصد است.واژه هاي كليدي :بيوديزل، تبادلاستري، بهينه سازي،كاتاليست ناهمگن بازي     
  45. prediction of suspended load in Qarahsue river by soft computing
    GOLI POURZAND 2018
      پيش بيني بار معلق رسوبات رودخانه قره سو با استفاده از محاسبات نرم
  46. Optimized Implementation Of IIR Filter On FPGA.
    Raza Heidari 2018
      Recently, solving under determined systems is interested problem in the researchers of several science , especially that is too hard solving problem in general for reaching sparsete solution. In special term , a linear equation system can be converted to an equal convex optimization problem that has just one solution. This improvement is start for many searches and caused sparse solutions.In this thesis, we Propose a novel algorithm for sparse infiniti impulse response (IIR) filter designe. If a filter be sparse the addres and moltiplieres of zero coefficient will be deleted at last cost and complexity of implementation will redused.In recently years a lot of algorithms for sparsing signal introduced. This algorithms 0in 0in 10pt" >In this thesis we propose a novel algorithm for sparse infinitive impulse response (IIR) filter designs. The objective of the sparse digital filter design problem is to reduce the number of nonzero-valued filter coefficient.The proposed design method is i  ired by   particle swarm optimization(PSO) algorithm.This algorithm is included into two stages ,a preliminary optimization stage is introduced to determine the positions of filter coefficients to be zero then is reduced the error with determined the zero in first step. At last designed Butterworth IIR filter be sparse with six, zero coefficients with pass band edge .3791 , cut of frequency .531   and attenuation -45dB the   implemented on virtex6 Field Programmable Gate Array(FPGA).
  47. Energy Storage Optimal Allocation in Power System Considering the Uncertainty of Wind Power Generation
    Vahid Jani 2017
      Energy storage systems (E  ) play a major role in power systems planning and operation. Regarding the continuing evolution of the storage technologies, the E   will be highly regarded in the future power networks, and also their various applications will be increased. The optimal E   allocation problems mean reducing the investment costs (or initial costs) as well as reducing the networks expected operation cost. By increasing the ESS capacity, the investment costs are increased, but the network operation cost is reduced; therefore, selecting inappropriate size and site for the E   would result in undesirable costs in the system. Among several advantages of the E  , improvement of the power system costs and voltage profile can be considered as the most prominent characteristics of the E  . Besides, increasing the renewable energy resources penetration, such as wind power, for reduction of the environmental pollution, postponed the construction of large and concentrated fossil-fuel power plants as well as transmission lines, increased complexity and harder distribution and its subsequent significant costs, improved power quality and increased reliability, and supply of the subscribers power demand at load peak times are some of other advantages of the use of E  . By using the E  , the generation power shortage resulted from disconnection of the existing units or separation of the renewable resources can be controlled; thus, the microgrids reliability criterion, especially in cases of high penetration of the renewable resources, is met. Simultaneous determination of size and site of the E   is a non-deterministic non-convex problem, which should be modeled in presence of the real constraints governing the power system. On this basis, in the present dissertation, for the first time, the optimal allocation problem of E   was investigated considering the practical constraints including generation and consumption balance, units generation power limitation, prohibited performance zones, ram   rate, as well as simultaneous reduction of three different and incompatible objective functions of cost, voltage deviation, and air Emission. Due to complexity of the problem, the presence of various constraints and incompatible objective functions, as well as possibility of involvement of the classical optimization methods in local points, from among the evolutionary optimization methods, two hybrid multi-objective algorithms known as MOGSA and MOPSO-NSGA-II were proposed. The modeling and formulation of the problem was performed in MATLAB software. In order to take the uncertainty into account, wind generation power was discretized using the five-point estimation method (5PEM), and the IEEE 30-bus standard system was selected for simulation. Furthermore, the multi-criteria decision-making techniques were used in order to increase accuracy and make sure of selection of the best solution from among the optimal solutions. The simulation results clearly show efficiency and effectiveness of the proposed method.
  48. Analysing the Unit Commitment Problem in Presence of Renewable Energy Combined With Electric Energy Storage Divices
    HamidReza Nikzad 2017
      The issue of   unit commitment is to determine the situation of switching on or off the available power generation units in a power grid. By solving this problem, the quantities of productive powers are determined economically, according to the existing constraints. One of the important criteria in solving the problem of orbiting unit commitment is to minimize the cost of electric power supply for the power system over a given time period. In recent years, the use of renewable energy for electrical energy has been given particular attention due to rising fossil fuel costs and also environmental problems caused by these fuels. On the other hand, , there are also some problems of the participation of these units in supplying demand for the network with the increased penetration of renewable energy sources in power systems. One of these problems is the uncertainty in the electrical energy produced by these units, and also the unavailability of these units in the hours of the day. The uncertain nature of the energy produced by renewable energy sources has led to a difference in the actual and projected output power of renewable unit commitment. Therefore, the combination of active units in planning in the circuit of the unit commitment in real time may be subject to changes that will remove the system from the performance at the optimal point. To overcome this problem, it is necessary to determine how the renewable energy sources participate in supplying the demanded load of network through the planning of unit commitment. Therefore, by reducing the uncertainty of the capacity of the production of renewable energy sources, the system can be brought closer to the optimal work point. Therefore, in order to compensate for the nature of periodic and incidence of renewable energy sources, electrical energy storage devices have been used in power systems. In fact, the purpose of using energy storage systems in power systems is to maximize the use of renewable energy sources. In this paper, the problem of the installation of unit commitment has been investigated, due to the many problems associated with the use of fossil fuels, with regard to the cost of pollution in the presence of renewable energy sources and energy storages. The MATLAB software, the Combination of the Genetic Algorithm and the Priority List Procedure with new use have been used to solve the problem in unit commitment. In this method, the initial population is produced in such a way that the supply and demand equivalence requirements and the minimum time down, the minimum time up of the units the constraints of the ramp rate, and the reduction of electrical power of units and the reserve of the spinining reserve erformed on the standard 10 units and 38 units. The results indicate that this process can help reduce the cost of the problem in the circuit of the unit commitment.
  49. بهسازي خاك هاي ماسه اي بوسيله ي رسوب ميكروبي كلسيت
    Anis Safari 2017
    بهسازي خاك هاي ماسه اي بوسيله ي رسوب ميكروبي كلسيت
  50. Investigation of effect of the plastic deformation on mechanical and wear properties of AL7075.AL2O3
    2017
  51. The destructive effect of confined water on the blast response of RC slabs
    Ahmad Reyhani 2017
      The destructive effect of confined water on the blast response of RC slabs
  52. Design and Evaluation of a Processing Unit using Reversible Systems
    Maryam Kimiaei 2017
  53. DynamicCharacterization.......................
    Amir Rizvandi 2017
      Small strain shear modulus of the soil dynamic parameters in geotechnical science is the foundation design and liquefaction assessment and dynamic loadings and other issues play a major role.This parameter can be measured and calculated by field research experiments or in the laboratory using a borehole or bender elements or column resonance, etc…Factors affecting the shear modulus can be confining pressure, void ratio, the average grain size and shape and arrangement of the particles noted.In this study, the experimental approach using bender elements; the influence of grain size on shear wave velocity and therefore the shear modulus dry sandy soils under pressure from all sides at different frequencies investigated.The results indicate that the shear modulus is sensitive to changes in grain size, as in a range of dimensions with its increase, the shear modulus increases and decreases in other domains.The purpose of this factor, which is a measure of grain to the highest shear modulus in the range of their own. In general, sandstone samples tested for maximum shear modulus for the range is about 1 mm of dimensions.
  54. study the interaction of soil - foundation - structure during ......
    Afshin Oladghobad 2017
      AbstractSoil-structure interaction effects of soil under the foundation of flexibility, relative vibrations between the foundation and the free surface arises. The inclusion of this effect and inertial forces can be a real shift system -Py-soil structures under seismic movements set free surface.Over the past three decades extensive research to characterize the soil-structure interaction effects engineering have been conducted. The results of this research in many earthquake regulations such as NEHRP, UBC, ATC,… come.Many construction requires the deep and wide excavation that the construction and operation may take several years. deep and wide excavation in an urban environment where the drilling location is surrounded by many building, it is important that the impact on the environment the vital challenge is investigation interaction between excavation and building during earthquake.Earthquake regulations have not studied this work. The aim of this thesis is investigation effect of adjust deep excavation on structural performance during earthquakeThe result for study Kermanshah hamyari building that adjust urban train excavation shown Increasing amounts of displacement, Increasing the period of the structure, Reducing the base shear.As a result excavation investigates adjacent structures is very necessary in the analysis.Key words: soil-structure interaction, deep excavation, base shear, period of first mode  
  55. حذف مركاپتان ازميعانات گازي به روش جذب سطحي با استفاده از كربن فعال
    Arash Rafiepour 2017
    Mercaptans, sulfides and disulfides are compounds that exist in fossil fuels, which creates disadvantages such as odor, corrosion and reduce the fuel heating value. In the present study, adsorptive Demercaptanization of condensate via modified activated carbon by concentrated nitric acid and then loaded with silver and copper metal ions and also, silver metal ions loaded copper-benzene three carboxylate (Cu-BTC) metal-organic framework were examined. Condensate with mercaptan content of 188 ppm was purchased from Fajr Jam Gas Refinery. The mercaptan content of samples was measured by titration method. After adsorption experiments, adsorption isotherms correlation parameters for Langmuir and Freundlich models and kinetic parameters for pseudo-first-order and pseudo-second-order kinetic models were studied. In this study, Cu-BTC adsorbent shows a good absorption performance in adsorption of mercaptan compounds from gas condensates. The maximum adsorption capacity for Ag loaded Cu-BTC and treated and then Ag and Cu loaded activated carbon were obtained 49.416 mg/g and 4.824 mg/g respectively. Also, the SEM, XRD, EDX and FT-IR tests were used to approve the structure of Cu-BTC MOF, metal loading confirmation, absorbent surface morphology, crystal structure of absorbent and the adsorbent structure stability.
  56. Investigation the Behaviour of Reinforced Concrete Coupled Shear walls with Openings using IDA analysis
    Safora Darabi ghasemi 2017
      Investigation that how Earthquakes Can effect on our structures made by human is very important for economical and safe design of the structures. By the previous research on the behavior of the structures it is obvious that a shear force acts at the base of structures during earthquake. Estimating a Reliable valu for base shear are very important to reduce structural damages caused be wind or earthquake. For the first time after the 1908 italy Earthquake engineers set it as 10% 0f structural weight. They changed it to 12.5% of structural weight in form of base shear.  By considering this provision structural performance was improved in later hazards and make structures after during.But structures show different behaviours against same earthquake.  Today millions of people live in structures made by Reinforced Concrete Coupled Shear Wall Systems. And some of most important structure like nuclear power plan, high rise tower and etc, are made in this way too. A coupled shear wall is a structural system made from to combined RC shear wall connecting by a beam named as coupling beam.  In this system thickness of concrete slab and shear wall are equal usually, for more rapid construction.  In many design Code such as the code and ASCE200 and UBC 1997 and regulation in turkey effect of earthquake force reduction factor in considered using ioss of the strength and ductility.  However, in none of the regulation , there is no way for calculating the behavior coefficient for those building that don’t have coloumn or girder and consisting ceiling and slab( tunnel form structure).vertical and lateral loads in tunnel form system are to lerated by the system.  In most cases, to access , and architectural elements or through ducts in the walls of the facility is a porter opening occurred in the structures of these systems proved to scientist.  The behaviour of such systems is entirely dependent on the geometry of the structure and behaviour of structures with different opening.  First a brief description on construction methods of this system was performed. Then some non-linear dynamic analysis on some models were performed by ABAQUS ver 6.14.3.  After that some smaller models made of walls and slabs modeled here in ABAQUS. For the sensitivity case study of the opening ratio on the behaviour of them were constand and only the opening ratio of the plan were different.  At final, after doing analyses curves were presented for the realative change of the behaviour.
  57. analyzing THE SMART BUILDINGS ON THE LOSS REDUCTION AND IMPROVING THE VOLTAGE PROFILE APPLYING TLBO
    DIYAR BURHAN KAKA KHAN 2016
      analyzing THE SMART BUILDINGS ON THE LOSS REDUCTION AND IMPROVING THE VOLTAGE PROFILE APPLYING TLBO
  58. Development of a Guide System Using Augmented Reality for Pictures in an Exhibition
    ASHWAQ WALEED ABDULAMEER 2016
    Augmented Reality (AR) applications rely on automatically matching a captured visual scene to an image in a database. The task of the thesis is to develop a technique which recognizes paintings displayed in an exhibition. Such a scheme would be useful as part of an electronic museum guide; the user would point his camera-phone at a painting of interest and would see/hear commentary based on the recognition result. Applications of this kind are usually referred to as "augmented reality" applications. Implemented on hand-held mobile devices, called "mobile augmented reality." We are interested in the image processing part of the problem.In this thesis, recognize image at the museum and a gallery is done. Photographed a database of Iraqi National museum and Free drawing exhibition in Ministry of culture and media in Baghdad. Recognize image evaluation parameters are time and accuracy. Features that are extracted from the images for the first time are Histogram in the different bin: histogram 256 bin, histogram 18 bin, and histogram 12 bin, Histogram of Oriented Gradients (HOG), Local Binary Patterns (LBP), Local configuration pattern (LCP). Also, these methods are compared with the three methods Scale Invariant Feature Transform (SIFT), Speed Up Robust Features (SURF), The combination of SIFT –SURF which has been used in past articles.The results showed that the best algorithms for image recognition are HOG-Histogram algorithm using SVM ltr">
  59. optimization of gas allocation to a group of oil wells in the gas lift process
    EHSAN HASHEM SOLTAN 2016
    Gas lift operation is one of the most common artificial lift methods that may be applied to obtain maximum production rate with minimum flowing – bottom hole pressure. The goal of this project is achieved by injecting gas to the wellbore in order to move oil to the surface.We chose gas lift in three wells in East of Baghdad field which located about (20 km) from the center of   aghdad and it extends from east – west to south – east by (100 km) length and (11 km) width.   In this study, a program has been developed using basic programming language to calculate the flowing – bottom hole pressure by using two correlations which are : modified Beggs – Brill and Aziz et ,al.   Gas and oil properties have been studied and the most accurate correlations and methods for prediction of these properties have been selected to use in the calculations. Standing correlation (1981) is use to calculate the oil density while the gas viscosity is calculated by Lee – Gonzalez – Eakin (1966).     Comparison of   the calculated and measured values for the flowing - bottom hole pressure showed that the modified Beggs – Brill give the most accurate results than Aziz .et.al method, therefore modified Beggs – Brill has been used in gas lift design calculations.   The average temperature - compressibility factor method has been used     to calculate gas pressure gradient with the depth. Then, the point of   intersection of this curve with pressure gradient curve calculated by modified Beggs – Brill method, has been used to specify the depth of injection point. Also the injection operation pressure on the surface and its effect on injection point detection for three wells, which is the most important parameter in the gas lift design process, has been studied. The positions and the distances between valves have been determined by using rules of graphical method.   The results showed that the gas injection rate for wells No.(10,11) are     (15 MMSCF/DAY) to give maximum production rate of (3430 STB/DAY) , (2970 STB/DAY) with minimum flowing – bottom hole pressure (4287 psi) , (4105 psi) ,respectively. Also the maximum injection rate for the well No.(19) is of   (7 MMSCF/DAY) with flow rate (3512 STB/DAY) and flowing – bottom hole pressure (4187 psi). current production rate for wells (10,11,19) are (2450,2100,3100) STB/DAY respectively.This study suggests exploitation of associated gas in East Baghdad oilfield to be cycled to lift oil as an artificial lift method.   The present work includes using PIPSIM software to build a model of studied vertical wells, producing from Tanumma formation, (WH1-11T, WH2-12T, WH3-19T) after choosing the suited correlation for each well. According to the statistical results, Mukherjee & Brill correlation is the best option for these wells.Gas lift design was done after studying gas lift performance-curves, which show the change of production with many parameters (gas injection rate, injection depth, and water cut). The result of this analysis is considered as a base of   gas lift design which include determining the optimum injection gas rate, the optimum injection pressure, the depth of injection and the valve technical specifications.According to the constraints (the min. allowable pressure for designing is limited by bubble pressure and maximum production by water Injection currently used in field), the required flow rate has been achieved by using gas lift. A simplified economic analysis of using two methods (gas lift & water injection) for 12 years, showed the superiority of gas lift option.   Finally, by using optimization techniques can improve the decision making process in gas allocation for continuous flow gas lift systems in East Baghdad Oilfields.
  60. .
    Nasrin Mahmodi 2016
  61. analyzing the advanced protection methods in multi terminal transmission lines .case study :electrical network of west regional electric company
    Hadi Mohammadpour 2016
  62. economic load dispatch based on enhanced bees colony optimization algorithm
    2015
  63. analysing the impacts of distributed generations with energy strong devices on the electric grid
    Saeed Javadi 2015
  64. distribution networks reconfiguration based on loss reduction and system reliability improvement by heuristic algorithms
    ALI KIANI POUR 2015
  65. economic load dispatch in thermal power plants based on minimization of fuel and fmission costs using evolutionary algorithms
    FARID MOHAMMADI 2015
  66. optimal modeling of demand response response in the electrical smart grids based on minimizing energy coast and increasing grid reliability
    EHSAN DEHNAVI 2015
  67. Optimal Placement and Sizing of Renewable Distributed Generation Units Consideration Units Considering Load Models Based on Meta Heeuristic Algorithms
    2015
  68. Optimal Power Flow in Smart Grid Distribution Systems
    Soheil Derafshi beigvand 2014
      An electric Smart Grid, which uses two-way flow of electricity and information in order to create an automated, widely distributed energy delivery network, has been led in essential changes in the conventional concepts of the power systems. Metering, control, and communication infrastructures in this system enable the independent system operator to manage the load demands and limit them if needed. Also, it enables the consumers to play their roles in the planning and operation fields, effectively. Therefore, this network provides the basis for effective implementation of Demand Response programs such as Direct Load Control. Optimal Power Flow as an optimization tool in power networks is an important issue in the new power system studies which different methodologies are proposed for finding its optimal solution. In this thesis, the OPF based on consumer participations in terms of distribution network and transmission system is analyzed. The proposed methodologies are the Lagrangian-based constrained optimizations. In the first methodology, load curtailment cost is modeled based on cost function of virtual generators. This approach is applied to 13-node power system under the Islanded mode and priority list of load curtailment scenarios and the results obtained by the proposed method are compared with an improved GA-based algorithm to demonstrate the accuracy and convergence to the optimal solution. In the second suggested approach, Social Welfare maximization subject to satisfy all operational constraints are presented. The proposed methodology tested on an IEEE-30 bus system under different operating conditions where are important for Transmission Companies. Some parameters such as minimum bus voltage, active power losses in transmission lines, and maximum active power flow, kept under observation while the market clearing price remains constant. The results are compared with OPF based on traditional optimization techniques and applying intelligent techniques such as PSO to demonstrate the accuracy, effectiveness, feasibility and convergence of the proposed algorithm.
  69. analyzing the islanding detection in power systems in presence ofd distributed generations and based on inteligent algorithm
    Mohammad Ranjbaran 2014
  70. transmission expansion planning in competitive electricity markets considering the uncertasinties related to wind farms
    Peyman Nazari 2014
  71. A comprehensive method for islanding detection in presence of multiple distributed generations in power systems
    Hasan Akbari 2014
  72. fixed order robust power system stabilizer design An LMI approach
    2014
  73. define the optimum fire angle in excitation system using artificial neural network
    Fatemeh Davodi noroleh 2013
  74. An Investigatigation on Variability Effect on FIR Filter Implementation
    Tahereh Hashemi 2012
  75. An investigayion on variability effect on DCT implementaition
    YASER DELDAR 2012
  76. power Quality in whnd power plants : Analyzing and Improvement
    Mahmood Goodarzi 2012
  77. design and fabrication of microstrip bandpass trisection filter with 2 GHZ center frequency using SIR resonators for multiple spurious suppression
    2011
  78. modeling and simulation of turbogenerator using computational intelligence
    Kaveh Darabi 2010
  79. modeling and simulation of silicon nanowire FET using neural network
    Jalal Rostamimonfared 2010
  80. modeling and simulation of low voltage RF CMOS VLSI amplifier
    2009
  81. Simulation of Recycle Gas Compressor by Computational Lnteligence
    Seyed Mohammad Jamshidi 2009

Update: 2026-11-12

افراد توان خواه
رنگ متن
رنگ پس زمینه
اندازه فونت
+ A -
پنهان سازی تصاویر
تنظیم کنتراست
فاصله بین کلمات
خط راهنما
فاصله بین خطوط
نوع فونت
بزرگنمایی انداره صفحه
+ -
توقف انیمیشن ها