profile - Razi University
Faculty Member of Razi University
Razi University
Hamid Toopchi-Nezhad
Associate Professor / Engineering / Dept. of Civil Engineering
Current courses
| Course Name | unit | term |
|---|---|---|
| Strength Of Materials 1 | 3 | first semester Academic year 2026-2027 |
| Reinforced Concrete Structures 2 | 2 | first semester Academic year 2026-2027 |
| Reinforced Concrete Structures 2 | 3 | first semester Academic year 2026-2027 |
| Seismic vulnerability and rehabilitation of structures | 3 | first semester Academic year 2026-2027 |
| Mechanics of Materials I | 3 | first semester Academic year 2026-2027 |
| Reinforced Concrete Projects | 1 | first semester Academic year 2026-2027 |
Master Theses
-
The Effect of Thickness and Type of Coating of MGO Panels on Their Fireproof Performance
Farshad Ghomami 2026Magnesium oxide panels have been considered as one of the mineral materials used in dry construction, partition walls, interior coatings and fire protection systems. However, the thermal performance, moisture resistance and mechanical stability of these panels depend on characteristics such as thickness, type of coating, thermal conditions and humidity level. The present study aimed to investigate the effect of thickness and type of coating on fireproof performance, moisture resistance and mechanical properties of magnesium oxide panels. This study is applied in terms of its purpose and experimental-descriptive in terms of its implementation method. MgO panel samples with different thicknesses, depending on the type of test, were investigated in the range of 8 to 16 mm. The tests included evaluation of thermal and non-combustible behavior, density, water permeability, environmental durability cycles, compressive strength, flexural strength and soft and hard impact tests. The compressive strength of the samples was investigated at ambient temperature and after exposure to temperatures of 600 and 1200 °C. Also, the flexural strength was evaluated under ambient conditions, high temperatures and relative humidities of 50 and 100%. In addition, the effect of cold traffic coating on moisture behavior and the effect of expanding fireproof coating on thermal stability of the panels were studied. The results showed that increasing the thickness was accompanied by an increase in compressive strength, flexural strength and capacity recorded in impact tests. The 16 mm sample showed the highest initial strength and the highest residual strength after thermal exposure in most tests. The temperature of 600 °C caused a limited decrease in compressive and flexural strength; while at 1200 °C, the decrease in strengths became more severe. The loss of compressive strength at 1200°C was about 55%, and the loss of flexural strength ranged from 38.44 to 60%, depending on the thickness of the sample. Humidity also caused a limited decrease in flexural strength; the intensity of the effect of saturated humidity was greater than that of average humidity, but much less than that of very high heat. The results of the intumescent coating test showed that this coating, when directly exposed to 1200°C, created an effective thermal protective layer on the panel surface. The coated samples did not experience significant extensive cracking, delamination, or delamination, and the thermal effects did not extend to the middle layers and core of the panel. Also, the mechanical strengths of the coated samples did not show a significant decrease after heating. Overall, increasing the thickness improved the mechanical capacity and thermal stability of the MgO panels, and the intumescent coating was also effective in reducing heat penetration and maintaining the structural integrity of the panel. However, generalizing the results to all MgO products and determining the fire resistance class requires additional tests and evaluation of the entire system, including panels, cladding, substructure and connections.
-
تحليل عددي ذخيره سازي انرژي در مبدل دو لوله اي مجهز به پره هاي درختي و مواد تغيير فاز دهنده
Sajjad Bavandpour 2026 -
Investigating the cyclic behavior of U-shaped yielding dampers by numerical method
MANA KASHANI 2026Abstract The use of passive control systems, such as metallic yielding dampers, is an efficient solution for improving the seismic resilience of structures and concentrating damage in sacrificial fuse components. The present research investigates the numerical and analytical seismic behavior of three-branch U-shaped metallic dampers. In the first stage, a valid experimental specimen was validated in the Abaqus finite element software to ensure the accuracy of the modeling process, and the results showed good agreement between the numerical and experimental hysteresis curves. Subsequently, a parametric study was conducted on 81 numerical models with geometric variables including arc radius (70, 90, and 110 mm), thickness (15, 20, and 25 mm), and width (40, 60, and 80 mm) under loading angles of 0, 15, and 30 degrees. All models were subjected to displacement-controlled cyclic loading to extract performance indicators such as effective stiffness, ultimate strength, and energy dissipation capacity. The results of the analysis indicated that increasing the thickness and width of the plate has a direct relationship with increased stiffness and energy absorption, while increasing the arc radius leads to a decrease in these parameters. It was also found that changing the loading angle, particularly when combined with variations in section width, influences the area enclosed by the hysteresis curve. In the final part of the research, based on the extracted data, new analytical relationships were proposed to predict initial stiffness and yield displacement with high accuracy. The validation of these relationships with numerical data confirms their efficiency in estimating the mechanical characteristics of the damper without the need for complex analysis. Keywords: Three-branch metallic damper, Parametric study, Energy dissipation, Effective stiffness, Finite element modelingt:
-
A reflection on how to apply the orthogonal earthquake effects in equivalent lateral force (ELF) procedure and modal response spectral (MRS) analysis method
Eslam Ahmadian 2026Abstract One of the challenges in the application of structural analysis methods is how to consider the effect of the earthquake orthogonal component. For this purpose, the 30%+100% rule or the root sum of squares method of the demand of the earthquake orthogonal components is generally used in design calculations, which lack appropriate accuracy. In this thesis, a concept called the spectrum companion curve, which describes the orthogonal accelerations affecting the structure at the same time as the moment of occurrence of the maximum acceleration response (spectral acceleration) in the main direction, is introduced, to be used as a tool for more appropriate modeling of the earthquake orthogonal component in spectral analyses. Appropriate accuracy of estimating the effect of the earthquake orthogonal component using the proposed companion curves has been documented with the maximum results obtained from time history analyses of different earthquakes in two types of soil (Type I and Type IV soil). Also, relations for the design spectrum companion curve have been proposed. Finally, the results of the analyses using the proposed relations of this study for the effect of the orthogonal component of earthquakes, compared to the results of structural analyses using the 30%+100% rule, indicate the superior accuracy of the proposed relations in this study. Keywords: Structural analysis, orthogonal component of earthquakes, spectrum companion curve, 30%+100% rule, 3D time history analysis
-
Investigating the hysteretic behavior of u-shaped yielding dampers using finite element method
Leila Alord 2026ميراگرهاي تسليمي U-شكل به دليل قابليت بالاي اتلاف انرژي، نقش كليدي در بهبود عملكرد لرزهاي سازهها ايفا ميكنند. در اين پژوهش، رفتار چرخهاي اين ميراگرها با استفاده از روش اجزاي محدود در نرمافزار آباكوس مورد مطالعه قرار گرفت. در گام نخست، مدل عددي با استفاده از المانهاي حجمي هشتگرهي و با در نظر گرفتن پيشتنيدگي پيچها ، بر اساس نتايج آزمايشگاهي معتبر صحتسنجي شد. براي كاهش تمركز تنش، يك هندسه پخدار پيشنهاد گرديد و سپس ?? مدل پارامتريك با متغيرهاي ضخامت، عرض، ارتفاع ، شعاع انحنا و زاويه بارگذاري تحت تحليلهاي استاتيكي غيرخطي قرار گرفتند. نتايج نشان داد كه افزايش ضخامت و عرض و همچنين كاهش شعاع انحنا، منجر به بهبود چشمگير سختي الاستيك، مقاومت نهايي و ظرفيت جذب انرژي ميگردد. در نهايت، يك رابطه تحليلي جديد براي پيشبيني سختي الاستيك ارائه شد كه نتايج آن با دادههاي عددي مطابقت مناسبي دارد. كلمات كليدي : ميراگر تسليمي U-شكل، روش اجزاي محدود، جذب انرژي، تحليل پارامتريك، سختي الاستيك
-
Seismic strengthening of steel moment resisting frame structures using buckling restrained braces
Jahanbin Jamshidi 2025Abstract The use of supplemental dampers is considered one of the innovative methods for seismic retrofitting of structures. Among the various types of dampers, buckling-restrained braces (BRBs) are more commonly utilized across the country. This study investigates the impact of BRBs installed on scissor-like bases on the structural performance of a three-story frame. The primary objective is to evaluate the influence of design parameters such as the length and installation angle of the BRBs on controlling structural vibrations. The studied frame, used in the SAC project and well-documented in the literature, serves as the basis for this research. Nonlinear time history analyses are employed to assess the seismic behavior of the structure, including base shear, column moments, maximum roof displacements, and energy curves, both with and without BRBs. The study aims to evaluate the effectiveness of different BRB configurations in reducing seismic responses. The structural modeling and BRB integration were conducted using the SAP2000 software. Force-displacement hysteresis curves of the BRBs were also extracted and analyzed to identify the optimal length and installation angle. The BRBs used in this research, referred to as Chevron Base BRB 3, feature two dampers installed on scissor-like bases resembling a figure-eight configuration. The optimal installation angle for Chevron-based BRBs was found to be 45 degrees, while the ideal BRB length was determined to be 2.5 meters. The findings of this study are specific to the analyzed frame and may not necessarily be generalized to other frames or structural systems. Keywords:
-
Finite element modeling of unbonded fiber reinforced elastomeric ring isolators for base isolation of heavy equipment units
Ahad Kiani 2025Earthquakes are one of the damaging factors that threaten the stability of technical buildings and vital arteries in many parts of the country. Therefore, seismic improvement of structures and technical equipment in vital arteries is necessary for the sustainable development of the country. Ground-mounted power transformers located in power distribution substations in urban areas are an example of technical equipment vulnerable to earthquakes. Due to the significant mass of these equipment, a significant inertial force is exerted on them during an earthquake, which can cause the equipment to slip or overturn and disrupt its performance by causing damage. One of these effective methods of seismic improvement of the described equipment is to reduce the accelerations affecting them during an earthquake using seismic isolation technology. The purpose of the present study is to study the feasibility of isolating heavy technical equipment with limited dimensions using only one elastomeric isolator reinforced with supporting ring fibers. To achieve the research objectives, ring isolators with different dimensions were designed for a selected transformer weighing 5000kg using the finite element software Abaqus. The outer and inner diameters of the isolator were changed as design variable parameters to study their effect on the lateral behavior of the isolators. In the present study, the range of changes in the outer diameter was from 1000mm to 2000mm and the range of the ratio of the inner diameter to the outer diameter in the studied isolators was 0.7 and 0.9. The results of numerical analyses show that with increasing the inner diameter of the isolator, the effective lateral stiffness and its lateral displacement capacity decrease. The achievable separation period in the isolated transformer can be increased by 1.5s and the maximum ground acceleration effective on the equipment can be reduced by 45%. Another part of this research is to develop analytical relations to estimate the vertical and lateral stiffnesses of ring isolators. The analytical relations presented in this study can be used in the initial design of the isolators. The results of this feasibility study show that fiber-reinforced elastomeric ring isolators have good potential for application in seismic isolation of technical equipment. However, for the practical application of these isolators in technical equipment, it is necessary to conduct laboratory studies and investigate the effect of various parameters on their behavior.
-
Finite element analysis of unbonded hollow-circular fiber-reinforced elastomeric isolators for seismic isolation of lightweight structures
Kasra Dalvand 2025Seismic isolation is one of the most effective technologies available in reducing the seismic response of many structures. Elastomeric isolators reinforced with steel plates are considered one of the conventional types of seismic isolators that have good isolation performance in large and heavy structures. The use of these isolators in lightweight structures lacks technical justification due to the inability to achieve appropriate isolation periods. The aim of the present study is to investigate the behavior of a new type of elastomeric isolators with effective application in lightweight structures. The isolators under study are fiber-reinforced elastomeric isolators with a circular cross-section with holes that are used as supports. Due to the elimination of the end steel plates and the smaller volume of materials used in the construction of the isolator, the total cost is reduced. The presence of a central hole in the isolator leads to a decrease in the effective horizontal stiffness of the isolator and, as a result, an increase in its seismic isolation efficiency. So that these isolators, which have both high technical potential and low economic cost, can be used to isolate light structures and heavy industrial equipment. In this study, using the finite element software Abaqus, these types of isolators have been designed and analyzed with the aim of isolating light structures for effective vertical forces of 150, 250 and 350 kN. Under each of the mentioned vertical loads, three different types of isolators with the same external diameters and different internal diameters have been designed. The internal diameter (hollow diameter) is considered as a variable and the force-displacement curves of the isolators in the vertical and lateral directions have been determined by finite element analysis and the reduction in their vertical and horizontal stiffnesses compared to the corresponding solid circular isolator has been obtained. In the following, two analytical equations for calculating the vertical and horizontal stiffnesses of circular isolators with holes, considering their supporting boundary conditions, have been obtained through regression with an error of less than 10%. These relationships can be used for the initial design of supported circular hollow fiber reinforced elastomeric isolators.
-
An experimental study on the effect of natural fibers (goat and human hair) on the behavior and mechanical properties of concrete
Rasol Kakavandi 2024 -
Development of analytical solutions for the lateral stiffness of circular unbonded fiber reinforced elastomeric isolators
Maryam Mansouri 2023The prevalence of frequent earthquakes throughout the world and the extensive human and financial damage caused by this phenomenon have prompted many researchers to explore ways to reduce this damage. Numerous systems have been employed to mitigate the aforementioned damage, among which seismic isolators can be considered one of the most important. Fiber-reinforced circular isolators represent a novel type of seismic isolator composed of alternating layers of elastomers and fiber fabrics. Utilized in an unbonded (non-connected) application, these isolators were placed above the foundation and below the superstructure, successfully isolating the superstructure from ground motions during an earthquake event. In an unbonded application, shear forces are transferred to the isolator through friction between the isolator’s contact surfaces and its contact supports. When the isolator is subjected to a lateral force, it undergoes a pseudo-rolling deformation, resulting in a nonlinear force-displacement curve. Consequently, the existing analytical relationships for traditional elastomeric isolators cannot be generalized to this type of isolator. In the isolator design process, determining the lateral stiffness under the influence of lateral forces is of particular importance. In the literature, only one analytical relationship has been proposed for this type of isolator, which, according to the investigations conducted in this thesis, does not provide a suitable approximation of the lateral stiffness in many cases. In this dissertation, not only has the existing relationship been modified, but also novel analytical correlations, which have been calibrated utilizing the outcomes of finite element simulations of fiber-reinforced circular isolators for the purpose of generating their lateral force-displacement diagrams. To verify the accuracy of the suggested associations, the force-displacement curves were assessed by comparing them with the hysteresis loops obtained from four experimental laboratory specimens. The equations introduced in this study can effectively approximate the lateral stiffness derived from laboratory experiments on isolators, exhibiting an average accuracy of 20% for shear strains of up to 0.5, and improving to an average accuracy of less than 10% for greater strains. Consequently, these correlations have sufficient precision for utilization in the initial design stages of unconnected fiber-reinforced circular isolators.
-
An investigation on the seismic response of RC-pole mounted transformers
Rojin Parval 2023Owing to the vital role of electrical energy in the daily lives of people, the stability of distribution networks after natural crises such as earthquakes is of particular importance. Aerial substations are among the most important equipment in distribution networks, and their proper seismic performance plays a significant role in the continuity of electricity flow during an earthquake. A review of the damage caused to the distribution networks by past earthquakes shows that the mentioned substations sometimes lack good seismic performance owing to design and construction weaknesses. In this thesis, the performance of distribution network aerial posts in previous earthquakes and existing standards in this field were reviewed and assessed. The objective of this thesis is to evaluate the seismic behavior of one of the aerial substations of the Kermanshah Province Electricity Distribution Company using finite element analysis. For this purpose, a 12 m long reinforced concrete pole with a nominal strength of 400 kgf was modeled using the finite element method in the Abaqus software. In the finite element model, the nonlinear stress–strain behavior of concrete is defined with the possibility of determining its damage index, and the stress-strain behavior of steel is introduced into the software with a bilinear curve. The finite element model was validated using the results of the static loading test of a 12 m long pole (available in the literature). Next, an aerial substation, a 315 kVA transformer (with a total weight of 1210 kgf) that was installed at a level of approximately 5 m from the ground level on a metal platform connected to two 9 m and 12 m long reinforced concrete poles, was introduced and modeled using Abaqus software. The transformer platform was connected to the 12-meter concrete pole of the post through two short C-sections that transferred the weight of the transformer to the pole by relying on the frictional resistance. Therefore, the contact surfaces between the concrete pole and the C-sections (as the support of the platform beam), which are prone to relative slip during earthquakes, were modeled in the finite element analysis. Considering that the studied aerial substation is located at the end of the line, the tensile force of the conductor wires connected to the concrete pole is applied as a static force in the finite element model on the 12 m pole of the substation. Finite element analysis includes a nonlinear time history dynamic analysis under the effect of the scaled accelerometer of the 2017 Sarpol Zahab earthquake, Iran, to document the weak point of the friction support of the transformer platform in transmitting seismic loads to its 12-meter base. The results of the analysis show that as a result of the relative slip at the contact surfaces of the C-sections and the 12 m long concrete pole, the transformer experiences significant rocking motions that could cause the risk of breaking the bushings and power outages during an earthquake. By examining the concrete poles of the post, it was observed that cracks and minor concrete crushing failures occurred at the base of the pole. Despite the damage to the concrete in this area, the pole maintained its stability and did not fail.
-
Finite element analysis of pre-compressed viscoelastic dampers
Pedram Sohrabi 2023Given the high seismicity of many regions in Iran,
-
Dynamic characteristics evaluation of a high voltage electrical power transformer using finite element analysis
Mahya Syefori 2023 -
Experimental evaluation of stress-strain behavior for half-scale self-reinforced masonry prisms
Parsa Salemi 2022 -
THE MECHANICAL PERFORMANCE OF PRESSED FIBER CEMENT BOARDS
Salahedin Sahragard 2022با وجود ظهور تكنولوژي هاي نوين ساختماني، نوع و تركيب ديوار همواره محل بحث مشاوران و فعالان صنعت ساختمان مي باشد. مؤلفه هايي مانند مقاومت در برابر فشار باد، تاثير وزن ديوار بر اسكلت و رفتار آن در زمان وقوع زلزله و به تبع آن كاهش تلفات انساني، مقاومت در برابر حريق، ميزان جذب صوت، ميزان عايق حرارتي، سرعت اجرا و... همواره از چالش هاي ساختمان سازي بوده است. در اين تحقيق(آزمايش) هدف اين بود با توليد فايبر سمنت برد به روش پرسي ضمن كوتاه كردن خط توليد و همچنين آسان كردن روش توليد، هزينه توليد را با حفظ مشخصات نسبت به روش هات چك به ميزان قابل توجهي كاهش داد همچنين در اين پژوهش صحت سنجي استفاده از شيشه و مو به عنوان الياف و جك هاي 30 و 10 تني جهت پرس كردن در توليد صفحات سيماني مورد بررسي قرار گرفت. جهت ساخت نمونه هاي مختلف فايبرسمنت برد، از سه مصالح ماسه، پودر سنگ و پوكه معدني بصورت جدا همراه با سيمان، آب ، الياف مو و شيشه استفاده شد كه نتيجه كلي بدين صورت بود كه استفاده از مو به عنوان الياف باعث كاهش مقاومت خمشي صفحات سيماني مي شود و الياف شيشه مقاومت خمشي صفحات سيماني را افزايش مي دهد. نتايج آزمون تعيين مقاومت خمشي بر روي آزمونه ها، نشان مي دهد كه صفحات ساخته شده با تركيب سيمان، پوكه معدني رد شده از الك 14 والياف شيشه ساخته شده با دستگاه پرس 30 تني الزامات استاندارد EN 12467 را در رده مقاومتي 2 (مقاومت خمشي 8.26 مگا پاسكال در شرايط خشك) و صفحات ساخته شده با سيمان، پودر سنگ رد شده از الك 30 و الياف شيشه ساخته شده با دستگاه پرس 30 تني الزامات استاندارد EN 12467 را در رده مقاومتي 3( مقاومت خمشي 10.3 مگاپاسكال در شرايط خشك ) برآورده مي كنند.
-
Preparation of nanocomposite membranes containing zinc oxide nanoparticle modified with herbal oils for application in membrane distillation
Parisa Sadeghi zolm abadi 2022Preparation of nanocompositemembranescontaining zinc oxidenanoparticle modified with herbal oils for application in membrane distillation
-
Energy optimization and auditing of the educational building and its redesign using a hybrid system to supply the required energy (Case study: Maharat Conservatory, Kermanshah)
Mohamad Taghi Shiri 2022 -
A comparative study on the response spectrum and response time history analysis methods in 3D frame structures
TOHID BAHRAMI 2021 -
A Comparative Study on The Performance of Bounded & Unbounded Elastomeric Isolators In Seismic Isolation of Above Ground Liquid Storage Tanks.
MASOUD KAKEHAZAR 2020One of the most common types of seismic isolators is steel reinforced elastomeric isolators (SREIs) which consist of alternating layers of elastomer and steel reinforcing plates. Unbonded fiber-reinforced elastomeric isolators (UFREI) are a relatively new type of elastomeric isolators. In this type of isolator to control lateral strain and provide vertical stiffness, FRP layers are used instead of steel plates. Additionally, to reduce the cost of isolators, the idea of removing the top and bottom connection plates and the unbonded use of isolators has been considered. In UFREIs, due to the rollover deformation and the reduction of the isolator horizontal stiffness, it is expected that the seismic isolation efficiency is increased as compared to the bonded isolators. In this research, the performance of UFREIs and conventional SREIs in improving the seismic behavior of liquid storage tanks were evaluated and compared. The isolated water tank was modeled using a mass and spring model of three degrees of freedom with convective mass, impulsive mass, and rigid mass. Time history analyses were performed on the fixed-base storage tank, as the benchmark structure, and the two base-isolated tanks with steel-reinforced and unbonded fiber-reinforced isolators. The results show that both types of isolators are effective in significantly decreasing the demand base shear in the tanks. However, seismic isolation increases the displacement demand in the convective mass. Regarding the comparison of the two types of isolators, it was observed that on average, UFREIs in slender and broad tanks are respectively 33.5% and 23.9% more efficient than the SREIs in reducing the maximum base shear forces. Also, there is no significant difference in the maximum displacement of the convective mass in the two isolation systems. The displacement and shear forces developed in the unbonded isolators were found to be less sensitive to the variations of the peak ground acceleration (PGA) as compared with the conventional bonded isolators.
-
Design and simulation of a power divider based on Plasmonic waveguide
Mohamad Reza Ghasemi 2020 -
Application of viscoelastic mass dampers in vibration mitigation of a structural floor system :A case study
Fatemeh Nikravesh 2020كف هاي طاق ضربي متشكل از طاق هاي قوسي شكل بنايي با دهانه حدود يك متر هستند كه بارهاي ثقلي را به تكيه گاه هاي خود (تيرچه هاي فولادي) منتقل مي نمايند. تعداد قابل توجهي از كف هاي طاق ضربي در ساختمان هاي موجود بدليل ناكافي بودن ممان اينرسي تيرچه هاي خود تحت بارهاي پياده روي داراي مشكل ارتعاشات قائم بيش از حد هستند. با اين حال، مشكل ارتعاش تنها محدود به اين نوع كف نبوده و در ساختمان هاي جديد نيز كه تمايل به استفاده از دهانه هاي بزرگ تر، كاهش پارتيشن ها و تيغه ها در ساختمان، و كاربرد مصالح سبك رايج است، كم و بيش مشكل ارتعاشات آزار دهنده كف هاي سازه اي مطرح مي باشد. در ساختمان هاي اداري جديد با توجه به پيشرفت فناوري، بسياري از كمدهاي مدارك و قفسه هاي بايگاني با كامپيوتري روميزي جايگزين شده اند. بنابراين، علاوه بر بارهاي مرده كف (بدليل سبك سازي)، بارهاي بهره برداري نيز نسبت به گذشته كاهش قابل توجهي يافته اند و ميرايي موثر كف كاهش يافته است. اين عوامل سبب ايجاد ارتعاشات سازه اي بيش از حد در كف هاي مذكور شده است كه در درجه اول موجب سلب آسايش ساكنين شده و در بعضي موارد سبب اختلال در عملكرد تجهيزات حساس نصب شده در سازه مي گردد. يكي از راه حل هاي موجود جهت كاهش ارتعاشات افزايش سختي و فركانس سازه كف با افزايش تعداد ستون ها و يا تغيير مقاطع تيرها و . . مي باشدكه اين امر نيازمند صرف زمان و هزينه زيادي است. به علاوه در اغلب موارد محدوديت هاي معماري عمدتا مانع اين راهكار ميشوند. راه حل ديگر در كاهش ارتعاشات افزايش ميرايي موثر كف با استفاده از انواع ميراگرهاي الحاقي مي باشد. در اين پايان نامه براي كاهش ارتعاشات دو كف سازه اي مختلف (الف: طاق ضربي و ب: عرشه فولادي با ورق هاي موج دار) تحت بارگذاري هاي مختلف پياده روي از ميراگرهاي جرمي تنظيم شونده ويسكوالاستيك استفاده بعمل آمده است. مدل سازي ها با استفاده از نرم افزار آباكوس انجام شده است. مدل اجزا محدود ميراگرهاي مورد نظر براساس نتايج آزمايشگاهي ارتعاش آزاد پيشين كاليبره شده است. سپس، جانمايي مناسب ميراگر، با هدف دستيابي به بيش ترين كاهش در ارتعاشات تير، با مدلسازي ارتعاشات تيري با فركانس طبيعي 52/4 هرتز و كاربرد ميراگر در 8 حالت مختلف مورد بررسي قرار گرفت. در ادامه با مدلسازي يك كف طاق ضربي و نيز يك كف عرشه فولادي داراي ارتعاشات بيش از حد مجاز، تاثير ميراگرهاي با نسبت جرمي 1% ، 2%، و 3% در كاهش ارتعاشات مورد بررسي قرار گرفت. ارتعاشات كف هاي مذكورتحت اثر 6 بارگذاري پياده روي و 3 بارگذاري دويدن با فركانس هاي تحريك 5/1، 2، و 3 هرتز بررسي شده است. نتايج اين تحقيق نشان مي دهد در حالتي كه ميراگر در وسط دهانه و موازي با تير قرار مي گيرد بيش ترين كاهش در شتاب حداكثر ايجاد شده در كف به دست مي آيد. چنانچه به هر دليل امكان نصب پايه ميرا گر ها در وسط دهانه تيرچه كف ميسر نباشد، ميراگرها را بايد در طرفين مركز تيرچه بگونه اي نصب كرد كه جرم انتهايي آنها متمايل بسمت داخل دهانه تيرچه قرار گيرد تا كاهش حداكثري ايجاد شود. بر اساس مطالعات اين پايان نامه ميراگرهاي جرمي تنظيم شونده مورد بررسي قادر به كاهش ارتعاشات هر دو كف سازه اي تا حد مجاز تحت اثر بار هاي پياده روي بوده و براي بارگذاري ناشي از دويدن تا 80% ارتعاشات را كاهش مي دهند.
-
Interaction analysis of the interconnected 20 kV power distribution poles during earthquake
Mehdi Niazi Hasarsefidi 2020In this paper, the vulnerability of air distribution transformers has been studied qualitatively and quantitatively (analytically). In the qualitative evaluation, according to the trajectories observed in previous earthquakes, the modes of failure of the transformer and their probable cause have been studied according to the evil of their executive environment in the country. Quantitative evaluation with dynamic analysis of a post sample The air has been affected by the acceleration of various earthquakes and the study of internal forces created in critical components. Based on qualitative studies, it was found that the most important weakness in air transformers is the lack of poor resistance of the lille, the lack of lateral restraint at the connection of the platform holding them to the base. These can cause trans (or overturning) of the transformer during an earthquake. The quantitative assessment also shows the vulnerability of the transformer if the retaining platform is not restrained to the base posts. Finally, solutions and suggestions for improving existing posts are provided. Keywords: Transformer bases, interactions of connected bases, seismic improvement, seismic resilience, seismic performance, earthquake damage
-
feature extraction related to touch screens to analyze user behavior
Shahram Barati 2019 -
Experimental Investigation of the Effects of Hybrid Graphene Oxide-Si Nano-Particles on the Microstructure and Mechanical Properties of 5083 Aluminum Alloy in GMAW Process
Reza Tahmasbi 2019 -
Determination of residual stresses and distortion in friction stir welded 2024 Aluminum alloy by ALE numerical simulation
Ahmad Zeinivand 2019Determination of residual stresses and distortion infriction stir welded 2024 Aluminum alloy by ALEnumerical simulation
-
the performance of half scale concrete-masonry prisms
Ehsan Kahrizi 2019 -
Static and Dynamic Analyses of Thin Uniformly Loaded Super Elliptical Functionally Graded Sandwich Plates
SEYED FARBOD AKHLAGHI 2019هستند.
-
Performance evaluation of unbounded fiber-reinforced elastomeric isolators against wind
Saba Chaghakaboodi 2019Performance evaluation of unbounded fiber-reinforced elastomeric isolators against wind
-
Optimizing the location of passive viscous dampers in 2D-frame structures using direct displacement based design (DDBD) method
Arash RazmAra 2019 -
The use of fiber glass textile reinforced mortar (TRM) to provide confinement in short concrete columns
ALI HAMEED FLAYEH 2018 -
the performance of viscoelastic tuned mass dampers
Hamid Hezarkhani 2018بررسي عملكرد ميراگرهاي جرمي تنظيم شونده ويسكوالاستيك
-
Optimal Placement of viscoelastic Dampers In a Frame Building using a Multi Objective Genetic Algorithm
Leila Pakravan 2018 -
Finite element modeling of the elastomeric isolators reinforced with plates of negligible bending rigidity
Mohammad Akbari 2018Many systems have been used for this purpose including seismic base-isolators which are among the most important ones. In this method, structures move isolated from the ground by placing a flexible lateral structure between the structure and the foundation. Isolators have several types, the most common of which are Steel Reinforced Elastomeric Bearings (SREBs). These isolators are made of intermittent and bonded elastomer layers and reinforced steel plates. Such isolators currently lack required economic justification for many conventional structures due to high expenses. In the last fifteen years, new elastomeric isolators have been developed called Fiber Reinforced Elastomeric Bearing (FREBs). In these isolators fiber reinforced layers are used, instead of heavy metal plates, to control the lateral strains of the elastomeric layers and to provide the necessary hardness along the vertical axis. In terms of bonding to the bearing, the isolators are categorized into three groups of "bonded", "partially bonded" and "unbonded". In unbonded mode, isolators lack the upper and lower steel plates, which reduce the expense and weights of isolators. In unbonded mode, no mechanical connection is made between bearing surfaces. In this situation, shear force is transmitted through friction at contact surface of the isolator with the bearing. These detachers undergo a unique deformation under rollover lateral displacement, which leads to the contact of the initial vertical surface of isolator with the upper and lower bearing of the isolator. Following a rollover deformation, the effective lateral hardness of the isolator has been reduced further, which means increasing the vibration isolation period and, in fact, increasing the seismic isolation efficiency. In this research, the finite element analysis has been used to model the behavior of force- one-way lateral deformation of Fiber Reinforced Elastomeric Bearing (FREBs) isolators. The modeling of these isolators is conducted in 3D format using MCS MARC finite element software. Providing a 3D model of Fiber Reinforced Elastomeric Bearing isolator with material specifications and geometric dimensional scaled with real dimensions in finite element analysis allows us to avoid some costly and time-consuming laboratory studies. The focus of this thesis is on the modeling of three-dimensional finite elemental behavior of the Fiber Reinforced Elastomeric Bearing circular isolators. Research literature in this area has nothing to say. In the analysis, the effect of the geometry of the rubber layers on horizontal and vertical responses of elastomeric isolators was studied. The effect of thickness is investigated by (
-
Finite element simulation of hysteresis loops in 2D fiber-reinforced elastomeric isolators under horizontal cyclic loading
Emad Saremi 2018Unbonded fibre-reinforced elastomeric isolator (U-FREI) is a relatively new seismic base isolator in which fiber layers are used as reinforcement to replace steel shims as are normally used in conventional isolators. Further, the top and bottom end steel connector plates of conventional isolators are also removed. In general, the horizontal response of U-FREI is nonlinear because of reduction in contact area due to rollover deformation and reduction in shear modulus of isolator under large deformation. Thus, evaluation of horizontal stiffness of U-FREI is a challenging problem. The unbonded application leads to rollover deformation that results in advantages such as decreasing the demand tension stress between internal layers and increasing efficiency of the bearing as a seismic isolator. Most of the previous finite element analysis studies on FREIs only have addressed the simulation of the monotonic behavior of this type of isolators. In this thesis, the main objective is to simulate the laterl load-displacement hysteresis loops of U-FREIs. The combination of an effective hyperelastic behavioral model in large deformations with viscoelastic behavior, the hyper-viscoelastic model will be produced that has the ability to consider the time dependency in the finite element analysis of isolator. The hyperelastic parameters are evaluated by curve fitting of theoretical curve to three uniaxial tension test of elastomer dumble-shaped specimens. The viscoelastic behavior is simulated using the Prony Series, and its parameters are determined by using the Nelder-Mead simplex method optimization algorithm, and the cyclic experimental results. The results show that the use of viscoelastic material model in conjunction to hyper-elastic material model leads to the effective simulation of horizontal stiffness and hysteresis load-displacement loops of FREIs. As another component of this thesis, The lateral response of isolator under various vertical compression stresses is studied using the finite element model that is developed in this study. Results show that both the effective horizontal stiffness, and equivalent viscous damping are increased by increasing vertical compression stress.
-
effects of thermal gradiant on composites beam reinforced by boron nitride nanotubes
Esmaeil Babaei jalileh vandi 2018تحليل رفتار مكانيكي ميكرو- سازهها بهعنوان يكي از اجزاي اساسي سيستمهاي نانو-ميكرو الكترومكانيك از اهميت خاصي در بين محققين رشته مهندسي مكانيك برخوردار ميباشد. در اين راستا، ميكرو-تيرها در سيستمهاي ميكرو-نانو مانند: ميكروپمپها، ميكروآينهها و ميكروسنسورها نقش مهمي را ايفا مينمايند. با توجه به مطالب ذكر شده تحليل رفتار ميكرو سازههاي ساخته شده از مواد تابعي براي طراحي دقيق و مناسب از اهميت فوق العادهاي برخوردار ميباشد. از مهمترين پارامترهاي طراحي دادههاي مربوط به آناليز ارتعاشات آزاد و اجباري سازه هاي ميباشد. همچنين براي انجام تحليل مناسب و حاصل شدن نتايج دقيقتر بايد همزمان از يكي از تئوريهاي محيط پيوسته غيركلاسيك و مدل تغيير شكل برشي استفاده نمود. هدف اصلي پايان نامه تحليل و بررسي تاثير گراديان حرارت بر روي تير كامپوزيتي تقويت شده با نانو لوله هاي نيتريد بور ميباشد.كه تير موردنظر بر اساس تير تيمو شنكو مدل سازي شده وقوانين حاكم بر اين تير براي حل اين مساله كمك گرفته شده است.در اين پايان نامه مقدار خيز وتنش و كرنش محوري و برشي بررسي شده است وبا افزيش درصدجرمي نانولوله هاي نيتريد بور مقدار خيز تير كاهش يافت همچنين تاثير پارامترهاي همچون، نحوهي توزيع نانولوله در راستاي ضخامت تير، شرايط مرزي مختلف ونسبت لاغري تير بر روي جابهجايي و تنش بررسي شده است و نتايج بدست آمده نشان ميدهد كه تغيير هر كدام از اين پارامترها تاثير بسزايي بر روي جابهجايي و تنش دارد. واژگان كليدي: مكانيك محيط پيوسته غيركلاسيك، تير، تئوري تنش برشي ،گراديان حرارتي.
-
طراحي و شبيه سازي يك مدار نورمورفيك آنالوگ با قابليت خود تعميري
Negin Veisi 2018Self-repairing is among the principal foundations of biological neural networks, upon which, adjacent synapses undertake functions of defected synapses to avoid disturbances in the network function, ending up compensating the incurred error. In the present research, a self-repairing analogue circuit is designed using an astrocyte-neuron relationship. The designed circuit is based on a software model of an astrocyte-neuron network with proven ability to detect errors and undertake self-repairing. The results obtained of the proposed circuit show that, when an error occurs in the synapses associated with a neuron, the currents of healthy synapses of the same neuron increases. This increase is made by receiving a feedback from adjacent astrocytes. This process maintains the network function and compensating the incurred error in the network. To the best of our knowledge, this is the first report to present a neural network-based analogue circuit with self-repairing capability considering the effect of astrocytes. In this research, the proposed circuit was designed and simulated in HSPICE software using standard 0.35 ?m CMOS technology.
-
طراحي و ساخت فيلتر پايين گذر با استفاده از رزوناتور تي شكل اصلاح شده و خطوط مارپيچ
Mohamadghasem Kordi peykani 2018در اين پايان نامه به كمك رزوناتورهايTشكل ونيمدايره اي يك فيلتر پايين گذر طراحي، شبيه سازي و ساخته شده است. اين فيلتر داراي فركانس قطع GHz34/1است و همچنين تيزي آن از سطح dB3 تا dB40 برابر GHz41/0 است. همچنين باند قطع اين ساختار از فركانس GHz68/1 تا GHz20 ميباشد كه نشان ميدهد فيلتري با پهناي باند قطع عريض طراحي شده است و سطح حذف هارمونيك در باند قطع اين فيلتر برابر dB20 است. اندازه اين فيلتر برابر 9mm2/15 ×3/9ميباشد كه با اين خصوصيات، اين فيلتر از ضريب شايستگي67954 بهره ميبرد. لازم به ذكر مي باشد كه در اين پايان نامه، فيلتر پايين گذر طراحي شده به چند رزوناتور تقسيم شده و اين فيلتر ساخته شده است كه مشاهده مي شود پاسخ ساخت و شبيه سازي تطبيق خيلي مناسبي ميباشند. كلمات كليدي:رزوناتور،فيلتر پايين گذر، اندازه كوچك، فركانس قطع.
-
The analysis of reinforced concrete .................
SHAFA FARHADI 2017تحليل تكيه گاه بتن آرمه اي ميراگرهاي ويسكوالاستيك متصل به ديافراگم طبقات
-
The application of sand in blast protection of concrete slabs.
Sara Bahmanooramani 2017 -
The demand of viscoelastic dampers on the foundation of structure
DANIAL SHAMS 2017 -
The destructive effect of confined water on the blast response of RC slabs
Ahmad Reyhani 2017The destructive effect of confined water on the blast response of RC slabs
-
The evaluation of response spectrum for pounding of adjacent buildings
Mohamad Papi 2017 -
مقايسه روابط تحليل در محاسبه سختي جانبي جداگرهاي اليافي غيرمتصل
MAJID KARAJI 2016A comparative study on horizontal stiffness solutions for unbonded – FREIs
-
عملكرد فوم هاي پلي يورتان با دانسيته بالا در كاهش خسارات ناشي از انفجار
SEYED MOHAMMAD HOSSEIN ANDAMI 2016 -
METHOD PERFORMANCE EVALUATION OF FIBER REINFORCED ELASTOMERIC ISOLATORS (FREIS) USING FINITE ELEMENT
MOHAMMAD MOEIN AKBARI 2016 -
Seismic strengthening of RC.moment resisting frames with various patterns of buckling restrained braces
2015 -
the influence of vertical ground acceleration on the performance of unbonded fiber-reinforced bearings
2015 -
The performance evaluation of RC water tank under air-blast loads
2015 -
Blast-Retrofitting of Reinforced Concrete Water Storage Tanks
2015 -
the improvement of geometrical and material properties of common hollow concrete blocks in iran
2014 -
numerical nonlinear analysis of compodite shear walls using fiber element method
Kambiz Daneshvar 2014 -
laboratoary study of location in the stability of earth slope
2014 -
cyclic analysis of masonary walls utilizing multi-laminate framework
2014
